Leaking, Corroded, or Burst Pipes in Davis, CA? Masters Plumbing Service Fixes It
In Davis's mixed housing stock, a single repair call might involve copper sweated joints, threaded galvanized fittings, push-connect PEX transitions, or CPVC drain arms — sometimes all in the same house. Our techs carry the materials and know the techniques for every pipe type commonly found in CA homes.
Acoustic & Thermal Leak LocationAll Pipe MaterialsPress-Fit & Sweat CapableLicensed in CA
Our Capabilities
How Masters Plumbing Service Approaches Pipe Repair in Davis
The biggest cost variable in pipe repair isn't parts — it's how much structure gets opened to find and access the failure. Precise pre-repair location tools reduce that cost significantly.
🔊
Acoustic Leak Detection
Pressurized water escaping a pipe creates a characteristic acoustic signature. Our listening devices amplify ground and structure-borne sound to pinpoint a leak location within inches — through concrete slabs, behind drywall, or under flooring. This means we open only the section of wall, floor, or slab directly over the failure.
🌡️
Thermal Camera Scanning
We use thermal imaging as a complement to acoustic detection — particularly useful for slab leaks and leaks inside insulated wall cavities where sound transmission is reduced.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Every supply line repair is pressure-tested before we close the wall or floor. We pressurize the repaired section, hold the test pressure for the required duration, and confirm zero drop before considering the repair complete. You don't find out there's a second leak next week — we find it before we pack up.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
PEX is also the material of choice for extending or reconfiguring supply runs during remodel work. Its flexibility reduces fitting count and eliminates the need for torch work inside walls.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
A burst pipe from freezing or sudden pressure surge requires immediate water shutoff and precise repair. We locate the failure, determine whether it's a single failure point or multiple freeze-damaged sections, and repair with a method appropriate to the pipe material — press-fit coupling for copper, expansion coupling for PEX-A, or a mechanical repair coupling for emergency situations.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
When galvanized supply lines are at end of life or polybutylene pipe (recalled for chronic failure) is in the home, a full repipe with PEX or copper is the permanent solution. We run new supply lines through the structure, transition all fixture connections, pressure test the entire new system, and patch access points in walls and ceilings.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
Real Pipe Repair Reviews from Davis, CA Homeowners
★★★★★
Water stain appeared on my kitchen ceiling from the bathroom above. I expected them to tear up the entire bathroom floor. Instead the tech ran a pressure test, found a 12% pressure drop over 10 minutes, then used the acoustic device and identified the leak at a failed sweat joint in the copper supply to the toilet — accessible through a 14-inch drywall cut in the ceiling below. Repair was maybe $280 including the detection. I'd been dreading a $2,000 floor demo.
— N. Bergman, Davis
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Davis, CA
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Davis, CA
Common Questions
Pipe Repair FAQ for Davis, CA Homeowners
A slow pinhole leak inside a wall can run for months before surface damage appears. By the time you see a stain, the moisture intrusion is typically already significant. If your meter shows movement with everything off, call us — we can pressure-test and locate it before it becomes a major remediation project.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
Repair options include direct slab access (jackhammer to the pipe, repair, patch), rerouting the supply line above slab through framing, and for copper systems with multiple pinhole failures, epoxy pipe lining from inside the pipe without excavation. We use acoustic and thermal detection to locate the leak before recommending a repair approach.
We assess galvanized condition when we're on-site — visible exterior corrosion, interior scale visible at the cut failure point, and water pressure readings all tell us how advanced the system deterioration is. We give you the repair-vs-repipe math honestly so you can make the decision that fits your timeline and budget.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Pipe Repair Covering Davis and All of Davis, CA
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Davis homes and businesses.
Precision Pipe Repair in Davis, CA — We Find It Before We Cut
Active pipe leaks compound fast — mold growth can begin in 24–48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Davis today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
